Effective ways to eliminate squeaking wooden floors

Wooden floors begin to creak over time, which is annoying for household members. Hearing unpleasant sounds every day after each step on the floor becomes simply unbearable.

Many people decide to independently carry out work to eliminate squeaks without dismantling wooden floors. The task is not easy, but if you act correctly, it is quite feasible. They start by finding out the causes of the sounds and what kind of wood floor repair work needs to be done to eliminate them.

How to eliminate creaking wooden floors without disassembling

Creak and places that cause it

Creaking is a physical phenomenon caused by friction resulting from movement that is accompanied by sound. The “music” of the floor occurs as a result of deformations in wooden floor structures that occur in different places and for different reasons.

Probable places for friction to occur.

1. Discrepancy in the connection of floor boards to each other.
2. Loosening of boards.
3. Places for installation and fastening of floor joists.
4. Fastening skirting boards to the floor.

Creaking usually occurs due to friction between the boards, which occurs due to loosening of their fastenings.

If the parquet creaks

Parquet can squeak for various reasons, one of them is insufficient or no distance from the flooring to the wall around the perimeter of the room. An expansion gap is necessary to allow the wooden flooring to expand under the influence of changes in humidity and temperature in the room. If there is no free space for the flooring to move, tension arises inside it, which causes creaking. Sometimes the dies can even rise up.

Bulging of parquet

To correct or create an expansion gap, first remove the baseboards, and then trim the edges of the flooring using a jigsaw or other suitable tool. The distance from the flooring to the wall should be at least 1 cm.

This problem can also arise when laying parquet boards. If the result is a breakdown of the locking system, then the damaged slats must be replaced. You can adjust the position of the boards using pins driven into the lock at an angle of 45 degrees.

How to choose a parquet board for an apartment? In order to make an informed decision, you should briefly familiarize yourself with the evaluation criteria for parquet boards, production technology and the influence of these factors on the characteristics. Our article will help you with this!

Trimming the deck

As with the board, free space can form between the base and the parquet tiles, which can cause squeaking. In order not to remove the coating, a hole is drilled in the problem die and cement mortar is pumped into it. The hole is puttied, the entire surface of the parquet is sanded and varnished.

Hole preparation

You can replace the reinforcement of the coating with screws using liquid nails, which are poured into a small hole drilled in the die. The douching method involves the use of special lubricants (wax and solvent) or water-based lubricant, which are injected through a small hole using a syringe.

Douching method

Creak of parquet boards

Re-upholstery with self-tapping screws is chosen if the parquet board creaks due to friction against the joists. When laying, the lamellas are positioned so that the joints run along the center of the logs. Both boards are fixed. To do this, drill holes at an angle of 45 degrees, and then fix the boards with self-tapping screws. In this way, at least 6 fastening points are made along one board with a length of 1 m. In this case, the caps of the fastening elements are recessed into the array.

Fixation to lags

If the locking part breaks, choose a method similar to the previous one, but use shorter self-tapping screws, which, at an angle of 45 degrees, enter the opposite board by at least 1 cm.

Prices for Tarkett parquet boards

Tarquette parquet board

Reasons why wooden floors creak

There are several likely reasons why wood floors make squeaking noises. When examining the floor surface, pay attention to such points.

1. On the condition of the base on which the floor joists are installed. These are lintels with boards fixed across them, forming the floor surface. The joists are made of wood and as they age and from daily loads, the base of the floor underneath them becomes deformed, becomes uneven, the level acquires a slope, which can cause vibrations and creaking sounds.
2. When initially leveling the floor, special pads are used that are installed on the joists. They consist of wooden blocks, which age over time, dry out, and the floor boards in these places collapse and begin to wobble, making a creaking sound.
3. Correct spacing between joists is of great importance. If the 50 cm parameter is not observed and thin boards are installed on them, the coating will fluctuate.

If the distance between the joists has not been maintained, there is a high probability that the wooden floor laid on top will creak.

Also, a lot depends on the quality of the wood used when choosing boards and joists:

• poorly dried material will dry out when laid on the floor, it will warp at the fastening points, which will disrupt the evenness of the coating;
• The fastening of the boards depends on the density of the wood. If this indicator is low, the connection of boards with lags and nails quickly becomes loose.

The accumulation of moisture on the base of the floor under the joists leads to the proliferation of fungi in the wood and its rotting. The quality of the connection between boards and joists is deteriorating, and the floor is sagging in some places. In this regard, all wooden components of the floor must be treated with an antiseptic for prevention.

If the wood has not been properly dried, the floor will sooner or later sag, which will also cause squeaks.

Small wood-boring beetles are a real disaster for wood. In a short time they can eat through the wood and damage the joists to such an extent that the floor boards will fail.

Important! Biocidal solutions, which are used to impregnate all wooden structures, prevent damage and protect the wood from harmful insects.

When installing the floor, be sure to pay attention to the following points:

• there must be reliable fastening between the logs and boards;
• there must be a technological gap between the floor surface and the walls;
• it is important to ensure reliable fixation of the plinth to the floor;
• It is impossible to allow the floor to be attached to the joists through a board, which was practiced in the old days in order to save money. This is an unsuccessful method, resulting in squeaking on unnailed boards.

Long-term use of the floor leads to its natural aging. All parts of the floor structure are subject to wear and tear. The gap between the boards grows due to weakening of the fastening - it becomes clogged with debris and dirt.

Remember that wooden boards and joists must be securely fastened

Not all of the listed reasons can be eliminated independently without opening the floor. For reliable and long-term service of the floor, it is necessary to initially provide for the installation of joists in a concrete base, a reliable structure with good ventilation with fastening of tongue-and-groove boards.

To eliminate the causes of the squeak, they first begin to find the source of the sound and study the condition and degree of wear of the floor. When a problem area is detected, press firmly on the boards. In case of deflection due to a loose fastening, use a long self-tapping screw to strengthen the fastening of the boards to the joists. If the cause is not eliminated, the floor will continue to creak. To clarify the circumstances, you will have to partially open the floor and examine it from the inside, for the presence of reasons for the creaking according to the above points.

How to independently identify the creaking factor

Before you get rid of a squeaking wooden floor using one of the available methods, you should find out what caused it. To do this, you will need to check the wood covering by inspecting areas where unpleasant sound occurs. In addition, it is necessary to check the reliability of fastening the floorboards to the joists, making some efforts to create a load:

• When wooden boards are bent with the heads and part of the nail legs exposed, and in addition, if some boards “walk” in the horizontal direction, this indicates the reason for the weakening of the fasteners.
• If the floorboards are securely fixed and under the influence of loads the structure deflects, then the reason is deformation of the joists or subsidence of the base that is located under them.
• When checking the floor covering, you should resort to using a building level, which allows you to determine where the height of the boards differs, which can often cause squeaking.
• In cases where it is not possible to determine from the floor surface what caused the unpleasant sounds to form, it is necessary to dismantle several floorboards and become familiar with the current state of the joists, as well as the base on which they are located.
• If the floor covering begins to sag while walking on it, then most likely the logs under the boards are located at a considerable distance from each other.

  
  The second reason may be that the material used was insufficiently thick floorboards. In such a situation, in order to get rid of the problem, it will be necessary to carry out a full reconstruction of the floor covering, during which it is necessary to replace the boards or lay additional joists.

• When inspecting the floor, you should apply increased pressure on the floorboards that are laid along the wall, as well as on the baseboards. There is a possibility that in these places cracks have appeared in the product hiding the gaps, or the wood has dried out. In such a situation, you will need to dismantle the baseboard.

Having found out the cause of the creaking, you can begin to choose a method by which it will be eliminated.

Possible ways to restore the floor

For proper floor repair in order to get rid of squeaks, there are the following recommendations.

1. In order to prevent changes in the condition of wooden floor structures during drying, deformation from high humidity, all parts are treated with an antiseptic before installation. Periodic repetition of impregnation is also required during the operation of the floor.

   How to treat wooden floor structures with an antiseptic

2. Rigid fixation of the logs to the base is ensured with the most complete fastening of the boards using self-tapping screws or nails with a screw notch.
3. The use of wooden wedges is a thing of the past. Now a set is used that has two wedges with a corrugated surface made of polymer materials.
4. The distance between the lags (laying step) is strictly calculated depending on the loads and the thickness of the boards used, which will protect the floor from deflections.
5. To securely fix each board to the joists, two self-tapping screws are used, which will create a reliable fastening in the transverse direction.

Advice! To avoid the labor-intensive complete opening of the floor, to inspect its condition from the inside, it is enough to cut a hole in the form of a hatch to see the degree of damage to the joists and the base.

The boards are attached to the joists using two self-tapping screws

Methods for eliminating squeaking are as follows.

1. Strengthening the fixation of wooden boards to the joists with self-tapping screws.
2. Increasing the adhesion of wooden structures using pins and wedges.
3. As a last resort, use polyurethane foam for fastening and increasing the support area.
4. Laying a new sheet of plywood or chipboard over the existing floor, which will distribute the load over a larger surface.

Useful tips

The following recommendations will be helpful in troubleshooting the problem

• to secure the boards, use only anodized, not black, self-tapping screws;
• holes in the floor should be 1-2 mm smaller than the diameter of the fasteners;
• Before screwing in the fasteners, blunt the end of each self-tapping screw to prevent damage to the concrete flooring;
• to avoid severe shrinkage, instead of polyurethane foam, you can use epoxy or polymer glue to fill cracks;
• If there is a slight creaking, the cracks at the joints of the boards can be rubbed with a soft wax candle.

How to determine the location of the squeak?

Wood is a popular floor covering, especially in private homes. The main disadvantage of this type of floor is that it creaks very often. Any owner can fix this on his own, having the simplest set of tools without opening the coating, but it is important to accurately determine the location and cause of the unpleasant sounds. Household members, attention and hearing are involved in the search.

1. The owner goes down to the basement, if there is one, and from above someone is walking heavily on all the floorboards. The creaking area will be clearly audible from below.
2. They walk along each floorboard, listening to the source of the creaking, paying attention to the movement of the boards under their feet. Examine the boards for cracks and large gaps. If the sagging of the boards is clearly visible, you can check them with a level.
3. Remove the plinth and examine the condition of the beam and base in the gap between the wall and the joists.

When the floor is thoroughly examined and problem areas are marked, repairs begin. Many methods for solving problems have been developed, the main thing is to follow the work technology.

Is complete dismantling of the coating required?

If, after installation, the wooden covering was treated with a protective compound - paint or varnish, then dismantling the boards will not be necessary.

Creaks can be quite easily eliminated from the top layer of the floor pie, thereby removing visual defects of the base and renewing the final paint layer.

In some situations, a major overhaul of the base will be required with the dismantling of the decorative coating and rough flooring underneath. For example, if a rough board on which a finishing coating is mounted - linoleum, parquet or laminate - creaks. In this case, the finishing floor is opened, the rough flooring is rebuilt, deformed elements are replaced with new ones, after which re-laying is carried out.

If the cause of the squeaking of the plank floor is the installed joists, then more serious repairs will be required, involving complete removal of the plank covering and reinstallation of the joists.

Methods for eliminating floor squeaks without removing the coating

Wooden floors age and begin to creak, but it is not always possible to make major repairs and completely open the floor. In some cases, proven methods for eliminating squeaking are used without such drastic interventions.

Eliminating the creaking of a wooden floor without disassembling is quite possible - there are many ways to do this

Sagging floorboards

To solve this problem, rigid fastening of the boards to the joists is not enough. Take long self-tapping screws with large threads. If the nails in the floor are firmly driven in, do not stick out, and are not bent, then they cannot be pulled out. Prepared screws are screwed in next to them, the length of which is selected according to the thickness of the log along with the board, about 2 cm shorter. For an accurate measurement, remove one board from the floor.

To accurately determine the number of screws needed and where to screw them in, it is enough to remove the plinth from the transverse wall. In the gap between the wall and the floor, all laid joists are clearly visible without the need to disassemble the entire covering. To make it easier to screw in long screws, small holes in the boards are prepared in advance. This ensures a stronger adhesion of the covering to the joists by screwing in self-tapping screws with their heads recessed deep into the board to prevent clinging to them when walking.

Important! If the creaking has disappeared and the floor has acquired some unevenness, cover the surface with sheets of plywood. It is screwed to the floor with self-tapping screws in increments of 15-20 cm, the heads of which are also recessed.

If the floorboards begin to sag, they are additionally fixed using long self-tapping screws

Reinforcement with wedges

Gaps formed between the boards and they began to rub against each other, making sounds? This can be eliminated by securing the floorboards using spacer wedges. They are driven into the resulting gaps. For work you will need a mallet and a hammer.

To make wedges, take thin slats of wood up to 15 cm long. They are first coated with wood glue and PVA to securely fasten them so that they do not get squeezed out by the floorboards when walking. The spacers are hammered in at a distance of 20 cm from each other. To prevent the wedges from protruding above the floor surface, they are cut off with a plane, and the remaining cracks are filled with a mixture of glue and fine sawdust. After drying, the areas where the cracks are sealed are sanded and covered with a water-repellent solution.

You can use wedges made from thin slats that drive into the gaps

Sealing cracks with a tourniquet

Sealing cracks can be done quickly and efficiently using a tourniquet. To do this, you can use a material made from flax, hemp, or a synthetic composition, which is pre-lubricated with glue. Using any sharp object, the tourniquet is inserted with force into the gap along its entire length so that the material does not stick out above the surface. When the glue dries, the gap is securely plugged, it is puttied and covered with paints and varnishes to match the main floor.

You can seal the cracks with a tourniquet

Sealing cracks with graphite and sawdust

If the gaps are small, and the creaking comes from the friction of the boards against each other, then it will be quite enough to fill the gaps with graphite or talc powder. Small gaps into which it is impossible to drive wedges are sealed with a prepared mixture of wood glue and fine sawdust. They are applied tightly into the gap using a spatula.

Small cracks can be repaired using graphite powder or a mixture made from sawdust and glue.

Sealing cracks with foam

To seal cracks, you can use polyurethane foam, which, when filling the space, reliably grabs and fixes the boards, and the floor acquires additional rigidity. But foam is used locally when it is necessary to eliminate the creaking of several boards. The disadvantage of foam is that it will compress under load, and over time the squeaking will return.

Gaps in the floor can be sealed with foam

Reducing the distance between joists

If boards of small thickness are initially laid on the floor or the distance between the joists is incorrectly calculated, then the floor covering sag over time and the floorboards begin to creak. This reason can be eliminated without opening the floor, using self-tapping screws with threads along the entire length.

Their size is chosen so that they reach from the beginning of the coating to the base of the concrete floor.

A hole is drilled near the joist, without touching it, and self-tapping screws or self-tapping screws are screwed into it all the way to the base, which will serve as additional support for the covering. The heads of the screws are broken off so that they do not stick out above the floor, and the sharp tip of the screws is removed so as not to damage the concrete.

If the joists were laid too sparsely, you won’t have to disassemble the floor: just screw in the screws near the joists all the way to the base

Ancient method

The ancient method of eliminating squeaks is time-tested and gives noticeable results for several years, provided that the floors remain level. To do this, take long strips of dense thick fabric, reminiscent of an overcoat. Pieces with a width of about 30 cm are laid out on the floor at a distance of 40 cm between them. Fiberboard sheets are placed on top and connected to the floor using self-tapping screws.

Important! This is a fairly simple and inexpensive method.

Elimination of board deflection with polyurethane foam

When a couple of boards sag, you can also use polyurethane foam as a temporary measure to eliminate squeaking. At the bend point between the board and the joists, a hole is made into which the tube from the cylinder is inserted. Before pumping the foam, the boards are secured with a block so that when it expands, it does not squeeze out the boards. After the foam dries, the filled space between the floorboard and the joists is sealed and the deflection is eliminated. The securing beam is removed and the holes in the floorboard are filled.

If some boards are bent, this problem can also be eliminated using polyurethane foam.

Loosening the tie

If the creaking occurs due to a weakening of the screed between the board and the joists, then they are strengthened using self-tapping screws. To accurately determine the location of the logs, remove the plinth from both sides. In the gap formed between the boards and the wall, the places where the logs are located are clearly visible.

Take two metal rods and drive them into the base of the floor to mark the center of the joists on both sides of each wall. A cord is pulled between the rods to indicate the timber along its entire length. To select the length of the screw, measure the total thickness of the board and joist and reduce it by 2 cm. Screw at least 3 screws into each board, strictly in the center of the joist, marked with a stretched cord. The screw caps are sunk so that they do not stick out above the floor surface. If there are protruding nails on the board, remove them. All holes are filled with putty to match the color of the floor.

To strengthen the tie between the boards and joists, screw in additional screws

Cementing subsidence of boards

Using cementation, subsidence of boards, which is caused by voids between the floor covering and the concrete base, is eliminated. To do this, in the place where the creaking occurs, make a small hole in the board with a drill, and using a syringe, gradually pour in cement mortar, making time intervals for the mass to harden. Fill until cement appears outside the hole. After the cement hardens, the floorboard straightens and the floor stops creaking for a while.

If the boards have sagged, you can fix this problem with a cement mortar, which is injected into the hole in the board using a syringe.

Additional anchoring

If using different methods still fails to eliminate the squeak, then a method of additionally securing the floorboards to the concrete base is used. To do this, fix the boards with metal anchors. These are special fasteners designed to secure the entire wooden structure to the load-bearing base. The height of the anchor is measured from the floor surface to the concrete floor with an increase for immersion in concrete.

To install them, a powerful drill is used to drill through holes a meter apart from each other through boards and joists all the way to the concrete. The anchor shell is inserted into it, and a metal pin is screwed into it. The wooden surface receives additional fastening and support.

Important! All holes in the floor are puttied, sanded, and painted to match the color of the floor.

Boards, if they creak, can be additionally secured with metal anchors

Installation of dowels

If simple edged non-groove boards are not connected to each other without a special joint using a tongue-and-groove system, they will dry out or diverge over time depending on humidity. To eliminate this drawback, install dowels. This is a cylindrical wooden product that is coated on all sides with wood glue or PVA. The dowel with glue is driven into specially prepared holes using a mallet or a special hammer for woodworking. Two adjacent boards are drilled at once in two directions towards each other, at an angle of 45 degrees, forming a symbolic cross. The ends of the unfinished dowel are cut flush with the floor surface, sanded, puttied and tinted to match the color of the floor. After such repairs, the boards will be fastened for a long time and will not come apart.

If the boards begin to diverge and creak over time, you can use dowels

Plywood covering

When the wooden floor is smooth, but very cracked and creaks in many places, a simple but expensive method of laying sheets of plywood with a thickness of at least 12 mm or chipboard on top of it helps. The load on the floor will be evenly distributed over the entire surface, which will eliminate the creaking emanating from some boards. The sheets are laid at an angle to the direction of the boards and glued with wood glue. When laying, take into account that the joint of the sheet does not fall on a problem area that produces a squeak - otherwise it will intensify. After installation, the floor is decorated.

It may be possible to eliminate the squeak by simply laying a thick layer of plywood or chipboard on top

Correcting the situation

To decide how to remove floor squeaks from boards without opening the floor, you need to determine the root cause of the sounding problem. It is necessary to conduct a visual inspection of the floor covering. The process should be accompanied by walking, jumping and tapping the entire area. The table shows the most common points.

Based on the results of the check, a method to solve the problem is determined. In a critical situation, you will have to completely dismantle the finishing or even replace the elements of the sheathing or rough foundation. At an early stage of identifying the causes, repairs are often limited to performing actions to eliminate the creaking of the floor without opening it.

Repair methods

Most of the causes of squeaky wood floors are hidden in plain sight. Therefore, repairs are often limited to work with decorative coatings. Let's consider the most effective measures that you can carry out yourself.

Eliminating squeaks without dismantling the floor Source sovetclub.ru

Reinforcement with additional bars

What to do if none of the methods helped? It may be impossible to do without at least partial opening of the upper surface of the floor. In this case, you can repair the sheathing, as well as strengthen it with additional bars, which are simply inserted between the joists. This will create additional support.

Important! If the boards are too thin, the distance between the lags is too large, then they will sag under the weight of the weight when walking. When repairing the sheathing, it is strengthened by inserting additional bars.

When calculating the distance between the logs, the thickness of the board is taken into account.

To further preserve the reinforced sheathing and prevent the appearance of squeaks, all parts are treated with waterproof solutions, and fabric linings such as geotextiles are laid between the parts and on top of the timber.

Sometimes it is necessary to partially open the upper surface of the floor and reinforce the subfloor with additional bars

Prevention of breakdowns

To prevent creaking, you need to follow a few simple rules:

1. 
   Place a backing made of foamed polyethylene, rubber or other non-woven material on top of the joists.

2. Observe the recommended distance between support bars. Check that all boards are level using a bubble level.
3. Leave gaps between the outer floorboard and the wall.
4. Use only dried wood for floor installation (moisture content of beams and boards is no more than 12%). In dry rooms, maple and conifers are used, and in wet rooms, larch, alder and ash are used.
5. Provide natural ventilation and maintain low humidity in the room.
6. Treat floors annually with antiseptic and water-repellent compounds.

To prevent premature wear, the gap between the support beams is selected in accordance with the size of the boards.

Floorboards with a thickness of 20-30 mm can be laid on joists in increments of 300-500 mm, and 45-50 mm in increments of 800-1000 mm. In areas where you plan to install heavy furniture, you can reduce this distance by 50-100 mm.

Spot repair of parquet

Parquet board is an elite option for wooden flooring. Like all wood floors, parquet can squeak when rubbed. In general, it consists of wooden elements assembled into one common flooring. Elimination of damage that causes sounds when walking is carried out pointwise, locally. Parquet repairs take place in several stages.

1. They carefully inspect each board, identifying and noting defective and creaking parts.
2. Prepare the necessary tools and materials: drill, volumetric syringe, cement or polyurethane glue.
3. Find the middle of the plank with a creak, drill a hole with a drill with a thin drill bit.

   Parquet boards can also creak over time.

4. Dilute the cement mortar to a liquid state.
5. Draw up a solution of cement or polyurethane glue with a syringe.
6. Insert the syringe into the prepared hole and slowly inject the composition, allowing air to escape.
7. Portions are introduced gradually, allowing the composition to gain a foothold and harden.
8. Check the work for no squeaks.
9. If the repair of one tile is positive, they begin to eliminate the squeak on the rest.
10. The last stage is to seal the hole with mastic and sand the parquet.

To get rid of the squeak that parquet makes, you need to fill the space under the plank with cement from a syringe

The floor creaks under the linoleum. Foam the cracks under the floor

I tried using polyurethane foam even before I read on this site. This advice can be found very often on the Internet. What to say? This will only make sense in one case, if the distance between the flooring and the concrete slabs is very small. No more than a few centimeters. If there is more, then you will need not one cylinder, but several at once. And it’s not a fact that you will be guaranteed to fill the space under the problem board. Personally, it didn’t work out for me for the reason stated. The builders used very thick logs (almost logs!!!) As a result, all the foam went to almost nothing. I still hoped that it would expand and increase in volume and still fill the space. The foam, as it should, swelled, but even this did not lead to the desired result. I repeat. The distance between the lags was very large.

How to get rid of squeaky floors? I took more drastic measures. Since my floors are covered with linoleum and are not visible, I simply replaced the squeaky board. I carefully removed it with an ax and a nail puller and nailed a new one of the same size. I didn't even paint it and left it as is. You still can't see it under the linoleum. Now everything is all right. The floor does not creak at all.

One more note. When I laid a PVC coating over wooden boards, and this was more than ten years ago, everyone told me that I couldn’t do that and the boards would rot in a couple of years. But that did not happen. They still serve great. Except the one he replaced. So you shouldn't listen to everyone. It’s better to conduct an experiment and be convinced that you’re right, even after ten years.

Yaroslav, Moscow.

Eliminating squeaky laminate flooring

Laminate is becoming the most popular floor covering. It has many advantages: it is inexpensive, if you follow the technology, it is not difficult to install the coating correctly, it looks beautiful, and there are practically no difficulties with caring for it.

But it can also begin to creak during operation. There are several reasons.

1. Incorrectly selected substrate. The synthetic gasket ages over time and becomes compacted in areas most exposed to pressure. The plates bend in these places and make a squeaking sound when walking. Cork backing is the most expensive, but stable material - it cannot be deformed.
2. Inexpensive laminated boards usually have locks of poor design. Eliminate squeaking using silicone-based lubricants. When lubricating the locks of the creaking laminate plates, apply the lubricant carefully to the seam and wait 15 minutes until it flows inside the lock. Excess grease is removed with a microfiber cloth, without leaving stains on the laminated surface.

   Laminate flooring can squeak if it has poor-quality locks - then silicone-based lubricants are used

3. Creaking occurs when laminate laying technology is not followed, when the gap around the perimeter between the coating and the wall is less than 5 cm. The plates rest against the wall, creating friction, which gives rise to sounds. To remove, part of the coating near the wall is cut off using a grinder.
4. Laminate flooring begins to creak due to an uneven subfloor, incorrectly selected underlayment, and unaccounted for class of laminate flooring at the time of purchase. This can only be corrected after dismantling the entire coating.

Why does a wooden floor start to creak?

Understanding the cause of the squeak will allow you to determine how to fix the problem. That is why it is so important to determine it at the stage of inspecting the parquet and listening for squeaks. So, why does parquet or parquet board squeak? As a rule, squeaking is caused by the following reasons:

• the tree dries out and decreases in size;
• the floor receives maximum load, which leads to weakening of the fastenings;
• during the installation of the floor, the conditions regarding the gap between the walls and boards were not met;
• large step between lags;
• thin wooden boards;
• air vibrations;
• violations of operating rules.

In all cases not related to a violation of the functionality of the lag, you can try to use one of the methods below to eliminate the squeak.

Parquet can squeak both in a certain place and throughout the entire surface area.

Creaking of boards damaged by fungus

Humidity under the floor covering and poor ventilation lead to the formation and proliferation of fungus, which, damaging the wooden floor sheathing, leads to its deformation and can cause the boards to creak. The coating can be affected by several types of fungus:

• the cellar mushroom forms large yellow myceliums covered with white spots. Over time they turn black;
• house sponge appears as a white fluffy mass, turning into gray mold. It has the ability to grow quickly under the floor;
• white house fungus in the form of mycelium, forming a cotton mass, is concentrated in one place in the form of a white pillow.

How to treat floors against fungus

These fungi not only affect the floor covering, but are also harmful to humans.

If you don't start fighting, the joists and boards will corrode, lose their strength, and the floor may rot and collapse. The most correct thing is to dismantle the affected structures and replace them with new ones. But with minor damage, mold and fungal plaque are scraped off to a clean place. The entire structure is treated with a solution of iron or copper sulfate, which is diluted in a proportion of 50 grams per liter of water. Lubricating the floor structure with a mixture of clay and vitriol gives a good effect. To prevent damage by fungal growths, wood is salted and impregnated with oil according to the Chinese method.

Important! There are many effective antifungal agents on the market for treating wood products.

If the fungus has affected a large amount of wooden flooring, it is better to get rid of it completely and re-lay it

Common causes

Initially, you need to determine what caused the floor creaking. Depending on this, further actions will be taken. It is also important to consider which area of ​​the floor the sounds are coming from.

Possible options include:

• area for fastening and installing floor joists;

• connecting boards to each other;

• area in contact with baseboards.

The main factor causing squeaking is deformation of the coating. An unpleasant sound occurs from the friction of wooden boards with each other.

Possible reasons for this phenomenon include:

• destruction of wood as a result of the formation of fungus, rot or mold;
• debris getting into cracks or gaps between floorboards;
• loosening of metal fasteners;
• wear of the linings that support the joists;
• sagging of the upper floor covering.