Scheme of the Grigorovich Deflector - instructions for creation

Good draft is the key to normal operation of the stove in a private home. If the draft is insufficient, then the fire will not flare up properly, and accordingly, it will not be possible to heat the room. In summer, the chimney can also serve as natural ventilation, thanks to the installed deflector, which will draw out air. Devices of this type can be purchased or made independently. It's not difficult, the main thing is to have the necessary tools and materials. The easiest way is to make a Volpert-Grigorovich deflector according to the drawings. It has a cone-shaped tip and is quite effective.

Volpert Grigorovich deflector

This type of device is the most effective and popular.
Therefore, we will talk about it in more detail. This deflector is often installed on the chimneys of gas boilers. The key feature of this design is the presence of an inverted cone under the umbrella. Therefore, during side blowing, a reduced pressure occurs in the channel, and combustion products rush out of the flue.

In case of strong wind “from top to bottom”, the pressure in the deflector area can, on the contrary, increase. This point must be taken into account when designing and installing a smoke exhaust system. But in most cases, the airflow occurs from the side. Therefore, the type of product under consideration is suitable for most gas ducts.

They look like this:

• diffuser diameter: bottom - 2*D, top - 1.5*D;
• diffuser height - 1.5*D;
• immersion of the channel into the diffuser - 0.15*D;
• the height of both cones of the umbrella is 0.25*D;
• the distance between the diffuser and the cap is 0.25*D.

Can it be installed on a chimney?

By installing a deflector, unlucky homeowners are trying to solve the problem of lack of draft. This happens when the chimney pipe is made incorrectly - the head falls into the zone of wind support of the roof, is raised to a low height, or a neighbor has built a tall building nearby.

The best solution for insufficient draft is to raise the chimney to the required height. Why is it undesirable to jam various attachments onto the head:

1. It is prohibited to place umbrellas and other exhaust devices on pipes that discharge combustion products from gas boilers. These are safety requirements.
2. When burning, stoves and solid fuel boilers emit soot that settles on the internal surfaces of chimneys and caps. The deflector will have to be cleaned, especially the rotating one.
3. At the bottom of a properly constructed smoke channel there is a pocket for collecting condensation and excess moisture. There is no point in covering the pipe from precipitation; it is enough to attach a nozzle at the end that protects the insulation of the sandwich.

The heads of stove flues can be equipped with umbrellas, but a turbo deflector is definitely not needed there. The topic of installing hoods on smoke exhaust ducts is covered in detail in a separate material.

How to build a deflector yourself

The deflector has its own parameters. So, its height should be 1.6-1.7 from the internal diameter of the chimney duct, and its width should be 1.7-1.9. Diffuser width – 1.2-1.3. But first, let's decide on the material from which it will be made:

If your chimney has a hole, birds often find it tempting to get inside. Small brownish black birds with a penchant for building nest in chimneys. Having these birds in your chimney can be quite annoying - they are vocal little buggers!

When you find yourself in difficulty with smokestacks, which are classified as an endangered species, there is little that can be done legally. The Migratory Bird Treaty Act, a federal regulation, prevents the removal of swift eggs and chimney chicks. The best thing you can do with quickies is to clean up after they leave. Technicians can be called in later to clean and remove nest residue from the chimney.

• Copper;
• Galvanized iron;
• Stainless steel.

Why copper if it is such an expensive material? The fact is that the deflector is located in one of the most inaccessible places in the bathhouse, and therefore, so that it does not have to be repaired, it is better to make it as resistant to atmospheric conditions as possible. And copper is the best in this regard.

Chimneys and most other birds are less likely to return to a nesting site if the nest has been removed. Several animals can get into your chimney, including squirrels and bats. Raccoons, usually females, enter chimneys to give birth and care for the pups. Terrible as they are, mother raccoons sometimes manage not only to get inside the chimney, but to pass through the smoke shelf or directly above the fireplace. If they have gotten this far, there is a good chance they will eventually break into your home. If not, you'll probably have to at least deal with various animal odors.

And here's how to make a deflector:

1. Draw on cardboard an outline of all the main parts, such as the cap, diffuser and outer cylinder.
2. Transfer everything to metal and cut using metal scissors according to these patterns.
3. Connect the parts to each other using rivets, bolts or welding.
4. Make brackets from a strip of metal - you will use them to secure the cap to the surface.
5. Attach a reverse cone to the cap.

The deflector itself must first be assembled, and only then installed on the roof. We first install the lower cylinder and secure it with bolts and nuts. Using clamps, we attach the diffuser to the lower cylinder, and on it - a cap with a reverse cone.

A raccoon is an animal you never want to hang as they are known for carrying various diseases. Raccoons are home to bugs like fleas and ticks that you or your pets can get, as well as diseases like rabies and roundworm.

Luckily, there are ways to remove mom and her babies from the chimney. If you don't mind the smell, items such as predator urine can get rid of raccoons. A humane method of removal is a live trap. You'll probably want to catch the mother while she's going through or even trying to scare her in some way. The babies still can't handle most of the fighting, so it's fairly easy to reach the fireplaces and grab them.

Purpose and use of deflectors

As a rule, chimney systems are considered the most important element of the entire heating system, because it is the operation of the chimney that affects the process of fuel combustion and the removal of all combustion products from the system and the house in particular.

The entire process of operation of a heating boiler depends on a high-quality air flow and on the complete removal of smoke from the system. Without the proper amount of oxygen, the combustion process is impossible, and food residues in a living space can seriously harm the health of residents.

In order to organize the correct level of draft in the system, you need to know some features of the chimney, the design and organization of which must be correct. First of all, it is worth considering the required cross-section of the pipe intended for air inflow and outlet. Important factors include the height of the chimney and its configuration. Now let's look at these requirements in more detail.

The choice of the required cross-section directly depends on the power of the thermal energy generator. The smoke exhaust duct or passage itself must be of a vertical type and straight enough so that no air pockets are created during operation.

In the event that compliance with these requirements does not produce a tangible result, it is worth resorting to the use of a deflector, which is mounted on the top of the chimney pipe.

The principle of operation of the deflector is to use the wind as an additional tool in leveling or increasing the level of draft in the system. Externally it looks like this. At the end of the pipe, a part of the system is installed that has a larger internal diameter than the chimney itself.

A strong wind allows you to create a rarefied space in the deflector, into which all combustion products remaining in the chimney move.

Among other things, the deflector has additional useful functions that have a positive effect on the entire operation of the chimney duct. With the help of such an element, you can protect the system from rainwater and snow getting into it in winter. As a rule, this helps the system function efficiently in any weather.

What is it needed for

The main thing when calculating the parameters of a chimney is to create sufficient draft capable of removing combustion products from the combustion chamber of a solid fuel stove due to a significant pressure drop. To do this, select the required channel diameter, material, cross-sectional shape and pipe height.

A strong wind can blow air into the mouth of the canal, thereby preventing the exhaust gases from escaping. An extreme case is the effect of draft suppression, when the boiler exhaust is not able to overcome the resistance and flows back into the room, which is, in principle, unacceptable.

It is not enough to close the mouth of the chimney from external air flows, but there are no optimal designs for this. It is better to use the power of the wind itself to avoid negative consequences and even further increase traction, which is what the deflector does very well.

Self-production of the device

To work you will need:

• galvanized or stainless steel sheet 0.5-1 mm thick;
• metal scissors;
• riveter;
• drill;
• a sheet of thick paper or cardboard.

The most important stage is drawing up a drawing. To do this, you need to measure the internal diameter of the chimney and calculate the product parameters according to the table.

If the internal diameter of your chimney differs from the parameters given in the table, calculations are performed as follows:

• the diffuser width is 1.2 d;
• width of the protective umbrella – 1.7-1.9 d;
• the total height of the structure is 1.7 d.

Both measurements and calculations must be as accurate as possible so that there are no difficulties during the installation of the structure and its subsequent operation. If the pipe has a square cross-section, then the deflector must be made square, although the angularity of the body slightly reduces the efficiency of the device.

If the design must have a reverse cone (Grigorovich deflector), the diameter of the protective umbrella is made 3-4 cm larger than the diameter of the cone. After assembling both elements, the cone is applied to the inside of the umbrella and outlined around the perimeter with a marker. Then make two cuts on the protruding part of the umbrella and bend the resulting strip inward. In the same way, make another 6-8 strips at an equal distance from each other, bend them inward and securely fix the reverse cone without additional fasteners or welding.

It is more convenient to attach a cap with a reverse cone to the diffuser with construction pins. To do this, before installing the cone on the umbrella, three holes are drilled around its circumference, the ends of the studs are inserted and the nuts are tightened. Then put the umbrella on top and fix the cone in the manner described above. At the top of the diffuser, on the outside, hinges made of tin or aluminum are riveted and the lower ends of the pins are inserted into them. This design withstands strong gusts of wind, serves for a long time and reliably.

In a similar way, you can assemble a deflector of any type, the main thing is to draw up the correct drawing. The only difference will be in the number and shape of parts. The finished device only needs to be mounted on the chimney.

Calculations and drawing

The TsAGI deflector is a very common device, and it can always be purchased in specialized stores and construction markets. In addition, it can be made to order by paying a tinsmith a fairly decent amount of money for its execution. But such a device can always be made independently, using calculation tables given in specialized literature and on the Internet.

If you decide to make this device yourself, then first of all, you should decide on the dimensions. It is necessary to build on the diameter and cross-sectional shape. The figure below shows a general drawing of a collet deflector for a circular duct cross-section.

• d is the internal diameter of the head of the ventilation shaft, and, accordingly, the narrow part of the diffuser.
• 1.25d – wide part of the diffuser.
• 1.2d – ring height.
• d/2 – distance from the narrow part of the diffuser to the lower boundary of the ring.
• 1.2d + d/2 = height of the entire diffuser.
• 2d – ring diameter.
• 1.7d – umbrella width.

How much does a deflector cost?

Ventilation devices are calculated together with the entire system. Deflectors of a specific model can be purchased for the required pipe diameter.

Table. Prices for deflectors

Deflectors are often made in artisanal workshops and small workshops (in this case, the product may not have a specific name or connection to the model). An indicator of the quality of the company’s work will be the product passport indicating the dimensions of the parts, steel grade and other details.

Making your own weather vane deflector

The weather vane allows you to reduce the height of the pipe by increasing traction, since it is always in the right relationship with respect to the wind, prevents precipitation from entering the pipe and decorates the roof.

Tools and consumables for work

To make one of the options for a weather vane on a chimney pipe with your own hands, you need to add to the above tools and materials:

• set of wrenches;
• pipe section;
• a metal (preferably stainless steel) rod or a ready-made pin;
• die for cutting threads on the rod;
• tap for cutting threads for fixing bolts;
• bolts for fixing bearings in the pipe;
• 8 nuts that will need to be screwed onto the rod to secure the bearings and secure the deflector housing.
• two bearings, the size of which is selected according to the diameter of the rod and the internal diameter of the pipe.

Step-by-step instructions and important notes

Operating procedure:

1. Initially, a drawing is made, according to which patterns for parts are then made from a sheet of galvanized steel.
2. Using patterns, apply the contours of the deflector elements onto a steel sheet with a special chalk or marker.
3. Metal scissors are used to cut out parts from a metal sheet.
4. The deflector body is assembled from the prepared elements by drilling holes and fastening them with rivets. You must remember to make brackets with which the body will be mounted on the rod.
5. Cut off a rod or pin of the required length so that it is enough to secure the bearings and fix the deflector body.
6. If a rod is used, the thread is cut using a die.
7. Next, two bearings are attached to the stud with the distance between them necessary to create sufficient support when the deflector-vane rotates. To secure each bearing, first screw on the first nut, then put the bearing on the axle, then screw on the second nut and tighten the nuts until the bearing is well secured.
8. Cut the pipe to the required length.
9. Holes are made in the pipe where the bearings are located. Use a tap to cut the threads for the bolts that will secure the bearings in the pipe. Holes are also prepared for attaching supports that secure the entire device.
10. A ring is made from a steel strip to secure the deflector to the chimney.
11. Cut sections used as supports for attaching the block with bearings to the ring securing the product to the chimney.
12. The final assembly of the product is carried out using rivets and fixing bolts.

There are many options on how to make a deflector for a pipe with your own hands. Everyone chooses for themselves what type of device is best suited. It is only necessary to note that such a design, placed on a pipe to remove combustion products, performs several useful functions - it increases draft when removing gases, protects the chimney from debris and precipitation getting inside. After installing the deflector on the chimney, the heating efficiency in the house increases significantly.

DIY ventilation deflector

Knowing about the structure and operating principle of the device, many owners decide to make a ventilation deflector with their own hands. From the point of view of hand-made implementation, the version of Grigorovich’s product is unrivaled, so we will consider the implementation of this particular option. The main advantage is that this ventilation works without electricity, all year round.

You should first prepare:

• stainless steel sheet type, can be replaced with galvanized steel;
• electric drill;
• fixing clamps, bolts, rivets and nuts;
• drawing tool for metal surfaces;
• compass;
• sheet cardboard;
• ruler;
• scissors for metal and paper.

Calculation of device parameters (Grigorovich)

We give you the simplest calculation option, without any formulas:

• The height of the deflector is 1.6 times the diameter of the chimney.
• the width of the diffuser is 1.2 times greater than the diameter of the chimney.
• The width of the cover is equal to two diameters of the chimney.

Based on the available dimensions and drawings, individual deflector elements are cut out of cardboard. Creating a rotating device requires certain skills, so it is better to practice on mock-ups and only then proceed to a metal analogue.

Manufacturing of the structure

The patterns must be attached to metal sheets, and then traced with a scriber. Next, the algorithm is simple - we use metal scissors to cut out the elements and details of the future design. The individual parts are connected to each other with rivets and bolts. If the mechanism is active, then it is better to fix the parts by welding.

Models of deflectors for ventilation systems made of cardboard

To securely fasten the rotating hood, you should prepare several curved metal strips that will act as brackets.

We fasten the brackets with rivets or bolts

As for the reverse cone, it makes sense to fix it at the umbrella.

Deflector

Installation work

The lower of the 2 glasses is installed on the exhaust chimney. The top glass is attached to it. For greater stability of the structure, the 2 parts are clamped with a clamp, and the same is done with the exhaust holes. The cap is pressed against the prepared brackets. If we are talking about a region where the wind direction often changes, it makes sense to equip the installation with a reverse cone, which will allow the unit to fully operate in any wind direction.

So, in this article we looked at what a deflector is in ventilation. To summarize, we can say that this is a simple and effective device that improves the ventilation of objects of any complexity, be it public buildings or residential buildings. A small element increases the performance of the ventilation system by 15-20%, reliably protecting the interior space from precipitation, small particles, debris and dust.

Grigorovich deflector manufacturing stages

The simplest product is the Grigorovich device, which is easy for most people to make.

Calculations and preparation of drawings

When drawing drawings and sizing this product, the following ratio applies:

• the height of the structure is approximately 1.7d;
• the cap must be made with a width of 2d;
• The diffuser width should be about 1.3d.

The symbol d refers to the diameter of the smoke channel. If a different size ratio is used during manufacturing, this will negatively affect the efficiency of the created device.

Based on the drawn drawings, patterns are prepared that are used when cutting galvanized iron into elements, from which the product is then assembled. To do this, transfer the outline of the elements in expanded form and in full size onto the cardboard, using a ruler, tape measure and pencil. When making a deflector for a chimney pipe designed by Grigorovich, prepare patterns for the outer cylinder, diffuser and cap.

Stages and nuances of making a deflector

Next, the following work with metal is performed:

1. Using prepared patterns, outlines of the necessary parts are applied to sheets of metal, outlining cardboard figures with special chalk. If special chalk is not available, you can use a simple pencil. Add 20 mm to the contour of the parts in places where they overlap, which will allow you to maintain the required configuration of the finished elements during assembly.
2. Using metal shears, the elements necessary for assembly are cut out of galvanized metal, thereby preparing the expanded outer cylinder, diffuser, and both parts of the cap - the umbrella cap along with the reverse cone.
3. Then, using a hacksaw, metal strips or a corner are cut into pieces of the required length, through which all the elements will be connected into the finished product.
4. The parts are given the required shape by folding and bending them in a certain way.
5. The next operation is assembling the product. The elements are placed on top of each other and, using an electric drill, the necessary holes are drilled. Using rivets placed in prepared holes, the parts are fastened together.
6. To install the Grigorovich device on a chimney, you can use two options - in the first case, through holes are drilled at the mounting location, through which the structure is fixed with fasteners on the chimney, and in the second option, a clamp is made from a strip, through which the deflector is fixed to the pipe.

Application of deflectors

The main quality of deflectors for which they are used is the ability to increase traction by diverting external air flows. Regardless of the design, any deflector works on a single principle - the air bypassing the obstacle creates a low-pressure zone, due to which the draft in the chimney increases. A good deflector can increase the efficiency of a smoke exhaust system by 20%.

In addition, the deflector has an additional function that occurs indirectly - an obstacle installed on the chimney pipe prevents precipitation and various debris from entering it.

A simple deflector consists of two cylinders, one at the bottom and one at the top, and a protective cone, also called an umbrella. The bottom cylinder is usually part of a chimney made of metal or asbestos cement. Galvanized metal is used to make the deflectors themselves.

There are several standard options for deflectors:

• TsAGI deflector;
• "Volper" with a round body;
• Grigorovich deflector;
• Open deflector Astato;
• H-shaped;
• Star-shaped "Shenard".

Different types of deflectors are used in the following types of structures:

• Collective and private ventilation shafts;
• Collective and private chimneys;
• Systems for the removal of gases and combustion products;
• Garbage chutes.

Peculiarities

Installing a deflector on a ventilation pipe significantly increases draft. The device deflects air flows. As a result, a low pressure zone is formed at the exit from the ventilation shaft. Thanks to this, the air inside the pipe rises. This way the pressure is compensated.

There are many designs of deflectors, but they all work according to the principle described above. Interestingly, most modern devices have a narrowing of the channel. This allows for an increase in the speed at which air flows pass over the head of the pipe. As a result, the craving increases. This effect is called the “airbrush principle”.

If you use the deflector on the ventilation pipe correctly, you can achieve a significant increase in the efficiency of the entire system. With the right choice of device and its optimal installation, the power increase can reach 20 percent.

Attention! The ventilation deflector shows the highest efficiency when installed on ventilation ducts with bends and large horizontal sections.

But the main purpose of the deflector is still to protect the air duct from the entry of debris, insects, small birds and precipitation. Since the device is installed externally, the case material is stainless steel or ceramic. In some cases, you can see regular plastic.

Advantages and disadvantages

Before assembling the unit with your own hands, you need to know not only its positive aspects, but also its negative ones. Let's focus on the positive first. The umbrella design effectively protects the pipe from precipitation and dirt, and an increase in traction can also be observed.

The main disadvantage of a deflector on a ventilation pipe is that when the wind blows from below, the flow hits the upper part of the structure and does not allow the air to exit normally. Therefore, problems with the operation of the system may sometimes occur. Fortunately, this happens quite rarely.

In addition, effective countermeasures were invented. Simply put, structures began to be equipped with two cones, which are connected by bases. Therefore, if you want to get a truly reliable unit, it is best to take this into account when creating a drawing.

Attention! The stronger the downward wind flow, the higher the pressure inside the ventilation deflector, which is installed on the pipe.

Errors and problems with the device

With the deflector, as with all devices, troubles can arise. One, the biggest and completely preventable one is incorrect work. This happens if the device was selected the wrong size. It can simply fall inside the chimney pipe, closing the path for combustion products to escape.

To avoid this situation, you need to pay attention that the diameter of the deflector pipe must be equal to the diameter of the internal chimney pipe. If the chimney is brick, and the installed device has a round cross-section, then you cannot do without the appropriate adapters

If the chimney is made of brick, and the installed device has a round cross-section, then you cannot do without the appropriate adapters.

The second mistake when installing a deflector is choosing a rotating model for areas with cold and snowy winters. Such a solution is fraught with icing of the device, and after a few days it will be covered with snow and not only stop rotating, but will also significantly interfere with the normal operation of the chimney.

To clean everything by removing snow and ice, you will have to climb onto the roof, and this is not the most pleasant activity on a cold and snowy day.

The third problem is the ineffectiveness of the deflector.

The problem may arise if the installation location or model is incorrectly selected:

• the body of the device is poorly blown by winds from different directions;
• in areas with gusty winds, an H-shaped deflector will be more effective;
• you should avoid installing the device in the aerodynamic shadow zone of trees and taller structures located nearby;
• the device must be located above the roof ridge and above other structures if they are present near the chimney.

If the deflector turns out to be ineffective, then it is necessary to look for the reasons for the backdraft of the chimney.

The fourth problem is the breakdown of rotating models. The fact is that the mechanisms that ensure rotation require maintenance. More precisely, you must not forget to periodically carry out maintenance on individual parts of the deflector and lubricate the bearings on time.

If the device was made by hand, and the material used turned out to be cheap and of poor quality, then everything can rust very quickly. In this case, you will soon have to replace it with a new deflector.

Another problem is when a simple cap is installed instead of a deflector. It may become icy and covered in snow. This will have to be fixed. It is dangerous if this situation occurs at night and all combustion products remain in the house. This is fraught with death for all household members.

Therefore, you need to install the deflector right away and not experiment with different canopies. If you don’t want to build an amplifier from scrap materials, you can always buy the model you like and install it on the chimney yourself.

It is necessary to take care of the normal operation of the boiler and the effective removal of combustion products at the heating design stage. Useful information on chimney construction is presented in this article.

Do it yourself or buy a device?

The question of whether it is advisable to purchase a deflector worries thrifty homeowners. This is not surprising, because the simplest device costs about 17-18 dollars. The average purchase price is $45-60.

The options for weather vanes offered by manufacturers and private companies are very diverse. Some models are made so skillfully that they look like a real work of art

In this case, making the device will not be difficult. And the aesthetic component does not always come first. Sometimes a deflector is needed for the chimney of a boiler heating a garage or other utility room.

The cost of the simplest deflector options starts at $17. To buy a Khanzhenkov, TsAGI or Volpert-Grigorovich model made of galvanized steel you will need up to $50. Moreover, these can be factory products or handmade ones.

The efficiency of the device does not depend on the manufacturing method. The main thing here is to choose the correct diameter of the product and the right model that can meet the needs of a particular chimney.

When purchasing, you should pay attention to the characteristics of the deflector:

• material type;
• metal thickness;
• diameter of the pipe for mounting on the chimney pipe.

Manufacturers also offer stainless steel options. They differ in cost - the price of rotary stainless steel models can reach $140 or more.

The most common deflectors used for chimneys in private houses, cottages and baths: TsAGI, round “Volper”, H-shaped, star-shaped “Shenard”, Grigorovich and open Astato.

For chimneys on the roofs of houses located in areas with gusty winds, N-shaped deflector options are often chosen

Whether to buy or build a traction amplifier is a matter of individual decision. For those who like to do something around the house, this task will be a pleasant and interesting activity.

If you don’t have any tools or skills for doing housework, then it will be easier and more convenient to purchase a finished product, choosing the most suitable model that will not stand out from the overall picture of the roof.

Now it’s not a problem to choose a deflector model that can organically fit into the roof composition

When purchasing or making your own device, it is important to consider the material of the roof covering. If it is a flammable material, then it is imperative to provide a spark arrestor. This is an important point that ensures the safety of all family members living in the house.

Installation of a deflector with a wind protection device

The deflector with wind protection is mounted as follows:

• Two bearings and a vertical axis are fixed in the chimney at two levels;
• A semi-cylindrical screen, a weather vane and a roof of the structure are successively installed on the axis.

The operating principle of this type of system is as follows:

1. When the wind direction changes, the weather vane rotates and pulls a curtain behind it, covering the chimney from the wind. As a result, smoke can escape from the leeward side of the chimney at any time.
2. Air flows pass tangentially over the semi-cylindrical screen and pull smoke behind them, increasing draft in the system.

To increase the efficiency of the structure, it is necessary to periodically lubricate the deflector bearings, and in the cold season, also remove ice that forms in the structure due to condensation. Taking into account the last nuance, we can say that such a nozzle on the chimney pipe from the wind can effectively protect only those structures that are located in warm regions.

Classification of wind nozzles

Despite the same purpose, exhaust hoods differ from each other.

When determining the optimal device model, you need to evaluate:

• material of manufacture;
• principle of operation;
• design features.

Material of manufacture . Aluminum, stainless steel, galvanization, copper, plastic and ceramics are used in production.

The optimal solution from the point of view of the cost/quality balance is considered to be steel and aluminum products. Copper deflectors are rarely used due to their high cost.

Plastic models differ from their counterparts in their lower price, variety of colors and shapes. Disadvantages of polymers: susceptibility to high temperatures and limited service life

A symbiosis of strength and decorativeness - combined metal caps coated with plastic.

Principle of operation . Based on their functional features, ventilation devices are divided into 4 groups.

Deflector types:

• static nozzles;
• rotary deflectors;
• static installations with an ejecting fan;
• models with a rotating body.

The first group includes models of the traditional type. Static deflectors are characterized by their simplicity of design and the possibility of self-assembly. The valves are mounted on exhaust shafts of residential and industrial aeration air ducts.

The second group (rotational deflectors) are equipped with a system of rotating blades. The complex mechanism consists of an active head and a static base.

Gusts of wind cause the paddle drum to rotate. During operation, a vacuum is created at the mouth of the mine, preventing the appearance of reverse draft

Static exhaust deflector with ejecting fan – modern technology. A fixed cap is installed at the end of the ventilation duct; a low-pressure axial fan is mounted directly below it inside the shaft.

Design of the static-rotational model: 1 – static deflector, 2 – fan, 3 – pressure sensor, 4 – heat-insulated flask, 5 – noise-absorbing ventilation duct, 6 – drainage, 7 – false ceiling

Under normal external conditions, the system functions like a traditional static deflector. As the wind and thermal pressure decreases, the sensor is triggered - the axial fan is switched on and the draft is normalized.

An interesting development that deserves attention is an ejection-type deflector with a rotating housing. A rotating hood is installed above the shaft.

The model consists of a horizontal and vertical pipe, which are connected to each other by a hinge mechanism. On top of the deflector there is a partition - a weather vane.

The horizontal pipe turns in the direction of the wind. Streams rush into the interior and create a vacuum - the thrust at the mouth of the mine increases

Design features . Models with the same principle of inducing natural ventilation have some differences in design.

Deflectors are of open or closed type, square or round, with one hood or several conical umbrellas. The characteristics of the most popular and effective modifications are described below.

Types and principles of design and operation of deflectors

Deflectors can be made in several generally accepted configurations and designs:

• TsAGI type deflectors;
• round type deflector (Volper);
• deflector designed by Grigorovich;
• open and H-shaped deflector.

The deflector itself has a design consisting of several separate parts. These parts include the lower type cylinder, diffuser and umbrella. The diffuser has the form of a cylinder located at the top of the element, and the umbrella protects the chimney from rain and snow getting into it. As a rule, deflectors are made from galvanized steel, which eliminates the possibility of metal corrosion by such debris.

The operation of the deflector does not have any features in its concept that even a novice master is not able to master. The wind flow goes around the entire deflector, colliding with it. This allows air to penetrate the upper cylinder of the deflector, increasing the draft in the chimney and drawing out all the smoke stagnant in the system. Due to the intensive movement of air inside the deflector, the traction force increases several times.

The design of this element allows you to increase thrust even when the wind flow moves in a vertical direction. For this purpose, there are special gaps in the upper part of the cylinder through which air penetrates into the ventilation and chimney systems.

It is worth taking into account such a thing as a downwind wind, which can make it difficult to remove smoke and reduce the level of draft in the chimney. Due to this wind flow, multi-directional wind flows are formed under the deflector umbrella, which clog the entire pipe.

Kinds

There are many types of deflectors for ventilation pipes:

1. The Tsaga deflector is very popular. The device has gained high popularity due to its simplicity of design and high efficiency.
2. The Grigorovich deflector is very popular.
3. The H-shaped apparatus is most effective when installed on chimneys.

It is also quite common to find open structures. Since there are quite a lot of various designs on the market, they are classified according to the following parameters:

• pommel shape,
• rotary or turbine operating principle,
• weather vane type.

The material from which the deflector is made plays a special role. For example, plastic products have a relatively low price, but their service life is not very long. You can also note the sophisticated appearance.

It is because of aesthetics that plastic deflectors can be seen on most pipes in private homes. Unfortunately, plastic cannot withstand high temperatures, so it cannot be installed on chimneys.

A rotating ventilation deflector enhances traction and effectively protects the channels from various debris getting inside. The main feature of the device is its spherical shape.

A rotary pipe vent may also be called a turbine vent. The device is capable of powering a turbine using wind energy. Inside, the air swirls like a tornado. This, in turn, increases draft in the duct. As a result, you can observe good traction even in summer.

Types of chimney caps

Before you make a chimney cap with your own hands, you need to decide what shape it will have, and then make a drawing. The most common forms that a chimney cap can have:

Chimney caps differ in design features and the material used in the manufacture of the product, but they all serve to enhance draft and protect the chimney from atmospheric phenomena.

When choosing an option, you should take into account the overall architectural appearance of the house. Thus, a chimney cap with a flat copper top is usually installed on houses in the Art Nouveau style. For a European-style home, it is better to make a canopy over the chimney with semicircular finials. Wind vanes with a gable roof serve for effective ventilation and protect the structure from filling with snow.

In wind vanes with a built-in weather vane, you can place a special damper, which in windy weather allows combustion products to escape unhindered. Chimneys with an opening lid are very practical; they allow you to clean chimney channels without much effort (see).

Protection of deflectors from low winds

Due to the presence of this feature of wind flows, deflectors began to be equipped with special protective devices that help increase the level of draft in the pipe in any weather. To do this, an axis is installed inside the chimney on two bearings located at different levels.

A semi-cylindrical screen, a weathervane and a cover are installed on the axis. It is this design that protects the entire chimney from the effects of the lower wind flow.

After the direction of the wind flow changes, the weather vane rotates, thereby closing the chimney from the wrong wind flow. Thus, any direction and strength of the wind is not able to block the path of the exhaust smoke, and the draft in the chimney remains the same power.

Do not forget that the deflectors are designed for round pipes, which can become a problem if you have an old brick pipe with a square cross-section. In order to solve this problem, special pipes are used that act as adapters.

For chimneys with a large square cross-section, which are built for fireplace heating systems, it is necessary to use adapters in the form of spacer legs that connect the pipe and the deflector itself. These legs are made of metal strips that can be galvanized or high-quality painted.

Brick pipes require an appropriate transition with an inlet in the desired direction, which allows you to connect a round deflector and a square chimney. In other words, it is not difficult to secure this element of the chimney system in the presence of any type and shape of chimney structures.

You don’t have to buy a deflector at a hardware store, because you can make it extremely easily with your own hands. To do this, you need to calculate the size and shape of the element, after which you can begin the manufacturing process.

On galvanized steel sheet it is necessary to draw the upper and lower cylinders of the future deflector, which can be easily done using an ordinary pencil. You can cut out the necessary elements using metal scissors, which can easily cope with this task.

Once these two parts have been cut and filed, which is required to properly join the two edges of one part, you can begin to secure these edges. As a rule, a welding machine, bolts or rivets are used for this.

It’s worth noting right away that connecting a galvanized steel workpiece using a welding machine is extremely difficult, because it burns through thin metal quite quickly. It is for this reason that rivets or small bolts are most often used.

The finished cone cap must be secured to the upper cylinder of the deflector. This is done using small brackets made of the same sheet steel. The brackets are secured to the pipe using rivets. Do not forget that the brackets should be attached only to the outer side of the deflector, so as not to create additional interference in the internal part for proper air flow and smoke extraction.

A reverse type cone must be attached to the element umbrella. In addition, the assembly of all parts of the deflector must be carried out directly on the pipe itself, which will allow for high-quality installation and fastening of each individual part of the structure.

Otherwise, it is possible to connect two elements of the system poorly, which will subsequently cause a malfunction of the structure and the entire chimney as a whole. In some cases, it is simply impossible to make this design on your own.

As a rule, this happens with brick chimneys, which require high-quality adapters or stands. From this we can conclude that it is much easier, more profitable and faster to buy this inexpensive element of the system than to try to make it yourself.

It is worth recalling that only galvanized steel can be used to make the deflector, which successfully resists the formation of rust, which negatively affects the life and quality of service of such a system element.

Video description

We tell you how to protect your chimney from precipitation, which is better: a deflector or an umbrella for the chimney.

What is needed to assemble the Volpert-Grigorovich deflector

This is exactly the material that will be needed to assemble the deflector Source minprom.biz
To assemble the structure you will need:

• one sheet of galvanized sheet 0.32 mm thick (this is the optimal parameter, although you can also use 0.25 or 0.5 mm galvanized sheet);
• short aluminum rivets no more than 4-5 mm long;
• steel strip (it is better to choose a thinner one, but not more than 4-5 mm);
• fastening - everything here depends on the pipe on which the deflector will be mounted.

Stock up on the following tools:

• riveter with any (movable or fixed) head;
• any tool or device for cutting sheet metal;
• a steel ruler, although a short level or building square will also work;
• any compass;
• roulette, scriber;
• drill or screwdriver (preferably the latter) with a set of drills;
• extension cord 220 V.

Possible problems associated with system smoke

Most often, smoke in the chimney system occurs for the following reasons:

• strong wind gusts, as a result of which air under strong pressure penetrates into the pipe, which causes a decrease in traction force and smoke in the living room;
• the smoke passage is too narrow, which is not able to provide the system with the required level of draft;
• insufficient lifting height of the chimney pipe, which does not allow the formation of the required pressure and draft force in the pipe.

Statistical type deflectors are designed specifically to solve all these problems, allowing the chimney to work extremely correctly and efficiently. The use of this element of the system is relevant for private or collective ventilation and chimney systems. As a rule, there are no restrictions on the use of this auxiliary device if its location does not interfere with other functions of the chimney.