Stove "Buleryan": reviews and disadvantages

The Buleryan heating system is an all-welded steel structure, on the sides of which there are multiple pipes. Cold air comes from the floor, it penetrates through the lower pipe pipes and heats up. And then it moves through the pipes pressed against the firebox of the heating device.

Already heated air comes out of the upper pipes, which is evenly distributed throughout the room. Already 15 minutes after lighting the stove, the air reaches a temperature of 120 °C.

Reviews about the main benefits

User reviews about the Buleryan stove will allow you to understand what the described design is. It is quite compact, but can easily cope with heating a room up to 100 m2. If you purchase equipment of greater power, it will be able to heat a room up to 400 m2. The period between stacking firewood reaches 12 hours. According to users, during operation you will only have to add firewood to the firebox several times a day so that the stove maintains a constant temperature in the room.

If you want to purchase a Buleryan heating stove, you should definitely read the reviews about it. From them you can find out that firewood burns out at a certain speed, which is affected by the set power. The type of wood also influences this. In just 3 hours after the device starts operating, the room warms up and the air in it reaches an acceptable temperature.

If the area is large, it is recommended to install several furnaces or purchase one unit, the size of which will satisfy your requirements. Such a stove, according to users, is not only convenient, but also versatile. It does not create smoke or soot in the room, saves firewood, and also has a convenient door for storing firewood, which simplifies operation.

Recommendations

And finally, we decided to leave you with some useful tips from experts:

This heating system can be used for houses with one or two floors. It is not customary to use it in houses with more floors.
The place for installing Buleryan-Aqua with a water circuit must be covered with metal sheets.
The stove should be no closer than 50 cm from the walls.
It is forbidden to heat this type of stove with coal, since it is wood-burning. It is permissible to use only firewood.
For efficient heat transfer, special corrugated pipes can be used.
To prevent freezing of the coolant in the heating system, there is an electric heating element with a power of 1 kW. Don't forget to make sure it's working properly. To be on the safe side, completely drain the coolant from the heating system, and then the stove and pipes will be able to withstand temperatures even down to -50 degrees.
Try to install the device in a separate boiler room or at least not on the street. Although the street option is possible (but only if it is constantly burning), it is better not to risk it.

Like other types of pyrolysis equipment, Buleryan-Aqua is sensitive to the quality of the fuel used, as well as errors that can be made during installation and features of the operating process. In general, the stove has good thermal characteristics, and I often use it for heating domestic and even industrial premises.

Main disadvantages

If you decide to install a Buleryan stove in the garage, experts recommend reading reviews about it. Among them, we should highlight the ability of the equipment to operate exclusively using firewood. It should also be mentioned that a large volume of generator gases does not burn, flying out into the chimney.

The firewood does not burn completely, the stove produces smoke, and the soot goes into the chimney pipe. This entails the need to extend the pipe 3 m from the height of the furnace. All these are additional costs, to which must be added the fact that the pipe needs thermal insulation. It does not matter whether the structure is made of metal or brick.

Reviews of the Buleryan long-burning stove also indicate that condensation from water, soot and tar accumulates in the chimney during operation. This happens because the fuel does not burn completely. The pipe cokes, and during kindling an unpleasant odor is formed, which is especially important after a long period of inactivity.

Consumers point out another disadvantage, which is that dust burns on the hot metal of the structure. This does not improve the atmosphere of the premises. The operating principle of the heating device leads to such consequences: the design is designed for heat transfer from the surface. It is not so easy to ensure long combustion and maximum heat transfer on one tab. To do this, you will have to master the skills of adjusting the damper. Reviews of the Buleryan dacha stove indicate that smoldering combustion causes many side effects.

Making a chimney

The smoke exhaust channel is made of a large diameter steel pipe. A specialized outlet is installed in close proximity to the stove. It is necessary to collect and drain condensate from the chimney. The chimney can be removed from the room either through the roof or through the wall. To avoid fire, an insert made of non-combustible material must be made where the pipe passes through the surfaces of the building. The Buleryan stove is highly efficient and easy to operate. It quickly warms up the room and saves fuel. You can choose either a finished product or make a boiler yourself.

Reviews about the analogue of "Buleryan"

When you have read the reviews about the Buleryan heating stove, it’s time to study Breneran. This equipment is an analogue of a convection device and was developed by Professor Butakov. The unit is identical to the Buleryan, but the latter is the fruit of German developments, while the Breneran was first released in Russia.

The design differs from the Buleryan in the large cross-section of air pipes and their impressive number. They are hidden in the housing, and the air intake occurs at a right angle. According to users, the case is made in the shape of a parallelepiped. The chimney is introduced into the upper plane.

For ash, the design has a built-in drawer, the system is complemented by a grate. It is the chimney entry point that makes using the stove not very convenient. When changing the position of the valve on a pipe, you can easily get burned on the top of the body or the base of the pipe. As consumers emphasize, the rotary damper does not have a lock, and when you try to set the blower yourself, it moves under the weight of the handle.

In the stove, the wood burns almost completely, leaving only a minimal amount of it. According to consumers, defects can be found in Russian-made convection ovens; they are expressed in the absence of elements, as well as poorly executed seams. If you read reviews about the Buleryan long-burning wood-burning stove, you will be able to understand that it does not have such shortcomings. The smallest models of units cost approximately 9,000 rubles.

Kindling technology

To use the stove, no specialized knowledge or skills are required. The boiler is easy to heat and maintain.

You can melt Buleryan as follows:

Fuel is loaded into the firebox. First, firewood of small thickness is used. The fuel should be dry, this will minimize the amount of condensation that forms and allow the fire to start quickly.
The wood is set on fire. The dampers that regulate the draft and the amount of air supplied are fully open.
After hot coals have formed in the firebox, thicker firewood is loaded through the door. The dampers are installed in the desired position to ensure long-lasting combustion.

After all the above steps, Buleryan will work as normal. The frequency of laying firewood depends on the intensity of fuel combustion.

Reviews about the features of using Buleryan in a residential building

For temporary residences and country houses, Buleryan is the ideal solution. However, many consumers, in their words, doubt whether it is worth installing such equipment in residential premises. Here the opinions of buyers differ, so it is worth taking a more serious approach to studying this issue.

After reading reviews about the Buleryan stove, you can understand that such an installation can have a negative impact on the healthy atmosphere at home. With a portion of air, ordinary dust is drawn into the structure, which first heats up and then begins to burn. Thermal decomposition does not require too high a temperature. Buyers emphasize that combustion products of dust particles are present in the air and can have a negative impact.

In order to get out of this situation, you need to purchase “Buleryan” and a regular stove. The first will heat the house, and the second will maintain a constant temperature. Experts emphasize that if the Buleryan is positioned correctly and the basic rules and frequency are observed, it is permissible to use such an installation in a residential building.

Reviews about use

You will be happy with your stove if you are careful when using it. Manufacturers claim that the described design is universal. Sometimes it is even compared to a solid fuel boiler. However, this belief is not entirely true.

The best fuel for a stove is wood. It is recommended to use non-resinous rocks. This should include:

birch;
poplar;
acacia

Pallets and briquettes are excellent. According to consumers, kindling is best done with logs, but briquettes are perfect for the combustion process. Do not use flammable substances when igniting. Reviews about the Buleryan stove say that before laying firewood, it is recommended to dry it on the stove, then its combustion will be more efficient.

The above-mentioned period of operation on one load of fuel will be relevant only when the furnace is fully loaded. Do not make the chimney pipe shorter than recommended. In order to ensure successful combustion, good draft is necessary, which is only possible with a total chimney height of 5 m.

Consumers emphasize that the pipe should be assembled against, and not in the direction of, the movement of gases. This will prevent resin from getting on the floor, which flows out of the furnace openings. If the chimney is installed correctly, the resins will return and burn. Owners of private houses who successfully use Buleryan note that you should check the smoker twice a year. This will eliminate problems with heating equipment.

Reviews about installation features

The Buleryan 100 stove, reviews of which you could read above, according to consumers, should be installed at some distance from flammable objects and materials. The distance should be 1 m. If the surfaces are covered with plaster, then this parameter can be reduced to 75 cm.

“Buleryan” is usually installed on a pedestal, which acts as decoration and serves as a functional element. Inside, consumers advise making a niche for firewood. Usually the base is made of piles.

Reviews about cleaning features

After reading the reviews and disadvantages of the Buleryan stove, you can decide whether you should purchase such equipment for your garden or home. But if you have already made your choice, then you need to learn more about how cleaning is carried out. No matter how high-quality heating equipment is, it requires preventive maintenance from time to time. "Buleryan" will begin to show signs of contamination over time. According to consumers, they are expressed as follows:

lack of traction;
deterioration of melting;
Difficulty closing the gate.

For cleaning, you can use one of several technologies. The main thing is that it is safe. Reviews and disadvantages of the Buleryan stove indicate that such equipment can become a source of increased danger. Consumers do not recommend using the so popular burning cleaning method. This method is dangerous, although effective. Some daredevils decide to take this extreme move.

Its essence is to heat the pipe to a temperature where the metal turns red. Under such conditions, the resin simply burns out, and the chimney is cleaned. Cleaning, according to stove buyers, can also be done mechanically. To do this, a special rod is used, with which you need to get into the pipe from the roof.

The length of the chimney above the surface should be approximately 3 m, so this approach is no less dangerous without the use of insurance. In winter, such manipulations should not be carried out. After reading the owner reviews about the Buleryan stove, you will choose another method for yourself - through a glass. If the smoker is thoroughly clogged, and it is impossible to clean it from above, then you can knock on the pipe. However, some of the resin will still remain in place.

The smoker is sometimes cleaned from the inside, although this option is quite complicated. From scrap materials you should make something like a folding meter with a ruff at the end. You can use an aluminum angle or pipe. The design should be quite light. The height of the pipe is decent, and if the device is heavy, then cleaning, according to the owners of Buleryan, will be quite difficult.

It is more economical and easier to use a rigid but flexible wire or cable. Its end must be rolled into a ring along the diameter of the pipe and the chimney must be cleaned through the condensate glass. According to homeowners where Buleryan is installed, this procedure has one drawback. It is expressed in the fact that a lot of dirt is formed in the process, but you have to spend no more than an hour on cleaning.

Reviews of "Buleryan" with a water jacket

Reviews from owners about the Buleryan stove make it clear that a design with a water circuit can be found on sale. Using such an installation, rooms are heated due to active circulation in heat exchangers. Such a stove, according to buyers, is an unusual and at the same time simple device. The body is cylindrical and consists of two levels. It resembles an ordinary barrel.

Reviews of the Buleryan stove make it clear that the lower level of the structure is the firebox, which is necessary for pre-ignition and raising the temperature to the level of the combustion chamber. The upper compartment is necessary for burning wood gas. The main task of the furnace is to heat large volumes of water. According to buyers, the device has elements that distribute energy for heating water and heating.

Communities › Garage › Blog › Buleryan stove Montreal

Hello everyone, I recently purchased a garage 6.3 x 11.5 m. A ceiling with a rise from 3.2 m to 3.5 m. The essence of the question is this. The Buleryan stove type 02 or Montreal is capable of heating 160 m2 or 400 m3. I have 72 m2 or 241 m3. Approximately how long will this stove be able to heat Will it be able to heat my garage at all? Who has used it, please tell me how it really is?

Comments 39

I could be wrong, of course. But if the garage is not used as a permanent home, then these muddy sobs are not needed there for nothing. The gas convector will save the father of Russian democracy. Lights up quickly, clean, warm, comfortable. No need to prepare firewood.

I had breneran, they are made under license from buleryan. When you put it in, the smoke enters the room with all the consequences (smoky ceilings and the smell of the stove).

You definitely need a normal stainless steel sandwich chimney with a minimum internal diameter of 150mm. And once a week, heat it with aspen - it burns off the soot from the pine.

The stove should Smolder, not burn! Therefore, those who supercharge this furnace are stupid niggas. And it is imperative to maintain a layer of ash cushion at the bottom of the furnace, otherwise the metal will burn out.

And you also need dry thick logs, I stored them right above the stove in a welded mesh box where they dried.

One load is enough for 6-8 hours of heating. Breneran has models for water heating: the pipes at the top and bottom are welded into a collector. If you put such a miracle in a separate firebox room, you can heat a decent-sized house.

While you heat it, it’s warm. It is difficult to remove ash. Actually the potbelly stove effect. If you attach a small fan to the stove, it will be more useful. And so is an ordinary metal stove...

good afternoon, I have exactly the same stove and a very similar garage according to the description =) We heat it with scrap boards from a construction site... it heats the entire room to 18-20 degrees in about an hour, depending on the outside temperature. Good luck.

I have a workshop of 70 sq.m., but it consists of two rooms with a wide opening, the ceiling height is approximately 2.8-3.0. I bought 02 bulik and placed it in a larger room (40 sq.m.). I use pine, chipboard and MDF scraps. In the part where the bulik is located it is very hot, in the second room it is 18-20 degrees. (this is at an outboard temperature of up to -10 degrees, the workshop is not insulated)

Bulik is a normal thing! Either the crooked ones set it up and drown it, or the same crooked ones drown it with an open gate or an uninsulated room.

But there is a difference between the two... The quality of production is falling. The metal is starting to be used thinner, worse... There are times when the weld seam bursts. But there is more overheating than quality.

Count it for your garage and take it with a reserve.

On my advice, they bought a lathe for the 800th, size 14X8X3.2, the ceiling (hollow slabs) is insulated with 5cm polystyrene foam, and the gates, walls made of gas for the riser, for 200, are simply plastered, a separate building, they work in overalls at most.

I bought this one and adjusted it to suit my size. The youngest model. I am not satisfied. I drown it with pine cuttings, I have to throw it in often. I didn't expect this. It warms up for quite a long time, raises the temperature by 20 degrees, no more. Garage 7*4, brick, insulated ceiling, insulated gate. At -12 I reached +5, in half a day, +20 is out of the question.

I have Burelyan 100, for 7 pipes. garage 4.6x7x2.2, wood frame, insulated with cotton wool (walls 50mm, ceiling 100mm). If it’s -10 outside, then after 2 hours you can walk around in the garage in a T-shirt, I think it’s 20 degrees. Maybe there's something wrong with the stove?

I have Buran AOT-06 type 00, I drown it according to their instructions. Wood consumes little heat.

it’s kind of stupid... I have the same boiler, only the garage is smaller - 6*4*3, only the ceiling and gate are insulated, the garage itself is located on the 2nd floor, made of slabs, in 30 minutes it heats up from -15 to +10-15, I heat myself with roof briquettes, last year I burned it with oak, I was tempted to light it and the oak was damp, but these stoves hate water