Rating of the best electric stoves for baths for 2022

A good electric stove for a bath or sauna will allow you to comfortably set up both a home and commercial steam room. There are many similar devices on the market today in different variations and price groups, therefore, choosing the right one (even from a budget series) will not be difficult. Moreover, it is not necessary that a cheap device will be deprived of most additional options. The stove devices under consideration can be used not only for heating steam rooms, but also for heating water. Typically, the designs of modern electric furnaces have a double casing, inside of which heating elements are located. In the upper part of the apparatus, a cage or tray is installed where bath stones are placed. The heating rate of the entire steam room will directly depend on their number and placement, because the heated stone immediately begins to transfer its heat to the external environment. Today's electric ovens can be installed either on the floor or hung on the wall. Most often, their control is controlled using a remote control.

Design features

The main advantages of electric stoves for baths are reliability in operation and a high level of safety. They can be placed in any room, even the smallest. An electric sauna stove does not emit carbon monoxide, a gas dangerous to human life, into the surrounding air, and the heat transfer efficiency is comparable to a stone or iron wood-burning stove.

The main structural parts of an electric sauna stove are:

• Housing made of two layers of metal.
• Heating elements or tubular electric heaters.
• Thermal insulation elements (bath stones).

Such units can be installed either on a horizontal surface or have the ability to be attached to a wall, it all depends on the specific model. There are electric furnaces with two mounting methods at the same time. Typically, such stoves have a control unit. It can be either built-in or portable (in the form of a remote control).

Stones for thermal insulation must be large enough. The outer casing is made of steel elements with a cross-section of up to 4 mm, and a small gap is left between the heater and the casing for ventilation and cooling of the metal.

The top of the stove is usually shielded with sheets of iron to ensure fire safety of the bathhouse or sauna. Heating elements can heat up to temperatures of about 800 degrees. Replacement options include belt plates, which provide a lower temperature but increase the service life of the electric furnace.

Basic operating principles

After applying voltage to the heating element, it begins to gradually heat up. This heat is transferred to coolants in the form of special stones. They accumulate heat and then release it either to the metal body (for closed-type ovens) or directly into the steam room (for open-type ovens).

For a classic Russian bath, the second option is more suitable. There are intermediate models equipped with a lid. Such electric sauna stoves can be opened at any time, increasing the convection of heated air from the heater.

Bath stones

The number of stones placed in the device depends on the size of the electric bath. The stones need to be laid tightly, but it is important to leave space for air movement.

For stoves, you can only use special stones that are not afraid of heat. Under no circumstances should they emit harmful substances or crack during heating.

The structure of the stones should be uneven; smooth stones should not be used. It is important to replace them promptly and remove cracked or chipped stones. It is necessary to carry out a refurbishment once every few months; jadeite, diabase, soapstone, and so on are ideal as bath stones.

Advantages and disadvantages

The positive aspects of electric sauna stoves are:

• The combination of rapid heating of a steam room and the ability to maintain the required temperature for a long time.
• Small sizes.
• Possibility of self-installation of such stoves. Unlike gas sauna stoves, permission from the gas service for installation is not required.
• There is no need to store fuel by placing it in the bathhouse; the stoves operate from a regular electrical network of 220 or 380 volts.
• An electric stove for a Russian bath does not require a smoke exhaust duct, which simplifies installation.
• It does not require cleaning from soot or periodic maintenance.
• Easy adjustment of the required oven temperature.
• Thanks to automation, unwanted overheating is eliminated.
• Such a stove does not emit carbon dioxide, it is safe for human life.
• The electric sauna stove has good heat protection, minimizing the possibility of fire in the wooden elements of the steam room.

At the same time, it is worth highlighting the disadvantages of such electrical units:

• The high cost of its maintenance, electrical energy is a fairly expensive type of fuel, and such stoves are very energy-intensive installations
• Often, powerful electric furnaces do not have enough electrical wiring life, which is designed for a lower consumed load.
• The heat generation of electric stoves is lower than that of gas or wood heating sauna stoves.

What types of electric furnaces are there?

Weight of loaded stones

Depending on the purpose of electric sauna stoves and the weight of the stones that are placed in them, all electric stoves can be divided into 3 groups:

1. Models with heaters for 20 – 40 kg.
2. Models with heaters for 60 – 120 kg.
3. Models for commercial use.

Stoves with a volume of stones up to 40 kg are perfect for small private steam rooms designed for 4 - 5 people. They are quite cheap, practical and easy to install. Their advantage is the quick heating time of the steam room, it will be no more than half an hour. An electric sauna stove like this can and should be watered frequently, and small portions of water will have to be added to it.

Electric furnaces with a weight of loaded stones ranging from 60 to 120 kg are more serious installations that are suitable for both large private bathhouses and small commercial bathhouses.

Prices for electric stoves for a bath of this type are 1.5 - 2 times higher than for stoves with a smaller volume of stone fraction.

Complete heating of such a unit occurs after 1.5 - 2 hours; such a stove gives off heat for a long time and better maintains a stable temperature regime. Adding water can be done without restrictions on the amount and time of adding.

Commercial models hold 200–280 kg of stones and are used in public steam rooms. They are able to work both in sauna and Russian classical bath modes. Such stoves are designed for steam rooms with a volume of several tens of cubic meters. Their price can be 40,000 rubles and more.

Bath electric furnace body type

There are two types of bodies for electric sauna stoves - closed and open type.

• The electric stove for an open-type Russian bath is a classic sauna stove, the stones in it are on the surface. The main disadvantage of such devices is that they cool down over time.

• Closed models of electric furnaces received the nickname “thermos” because of their design. They are made in the form of a round flask with a lid that opens on top. The stones themselves are located inside and are heated by heating elements built into the walls of the body. The big advantage of such devices is that the lid prevents the stones from cooling, and the steam is finely dispersed. Thanks to these properties, this is an excellent option for a classic Russian steam room.

Rating of the TOP 10 best electric sauna stoves for 2022

Criterias of choice

The modern market offers many options for such units. The question of how to choose an electric stove for a bath is not so simple. The main selection criteria should be taken into account, these include:

1. Preliminary calculation of the volume of the steam room.
2. Furnace controls.
3. Type of heating circuit.
4. Design issues.
5. Availability of a certificate of product conformity to Russian standards.

There is a simple relationship between the volume of the steam room and the power that the stove installed in it should produce. For 1 cubic meter of steam room there should be 1 kW of power. This calculation is approximate, but with its help the buyer can determine the choice of electric stove of the required performance.

The control panel for a sauna stove can be either remote (remote), installed in another room (in the dressing room), or built into the body of the electric stove itself.

Heating elements for electric sauna stoves can be of three types:

• Tubular (heating elements), made in the form of a tape. Heating elements are capable of heating air to very high temperatures, but they have a serious drawback - they are fragile and their service life is short, and the heating process is slow. Reliable stainless steel heating elements are very expensive. Tape elements are more profitable, heat up faster and are more reliable than heating elements.

• Combined type. The combined type of heaters is the most expensive, but it is the one that ensures the fastest and highest quality heating of the air in the steam room.

Electric sauna stoves, as well as wood-burning ones, can be made in any style. They can be located in the middle of the room, stand in a corner, or hang on the wall.

Additionally, you can purchase inlays made of soapstone or soapstone; this will not only decorate the stove, but will also provide additional protection from the effects of high temperatures on the walls of the steam room. Such stone panels retain heat well and can be an excellent complement to the stones inside the stove.

When choosing a stove, you should pay attention to the availability of a valid safety certificate for it and the materials from which it is made.

Recommendations for installing an electric stove

A small electric furnace with a power of 4.5 kW is installed in a small steam room. Before starting work in the steam room, it is necessary to remove the wiring and provide fresh ventilation.

Ventilation needs to be taken care of in advance.

To carry out the work you need the simplest tool and some materials. You need to stock up on sheets for creating a screen and self-tapping screws, for installation of which you will need a screwdriver. To cut holes in the screen plates, you will have to use a jigsaw. To connect the cable to the terminals, you need a Phillips screwdriver.

Step 1 . Screen installation. It can be made of metal sheets (stainless steel is used), which is most often used. However, other fireproof materials can be used. For example, Flamma fiber cement sheets, which have excellent fire resistance and safety. To fix the plates, you need to drill holes. After this, you should fix one part of the screen with self-tapping screws through ceramic bushings (6 pieces per sheet are enough). This is necessary to create an air gap between the steam room wall and the fiber cement.

Screen installation

The second sheet of screen, on which the stove will be suspended, is attached directly to the wall through a layer of foil-coated basalt cardboard. This heat insulator is attached using a stapler.

First, you need to cut a hole in the screen element for the supply pipe. You also need to provide a wiring outlet. After installing the sheets, the supply ventilation grille is attached.

Finished screen
What else is good about fiber cement boards: they are cheaper than stainless steel sheets and splash marks are not visible on them.

Step 2 . Electricity supply. To connect three phases, a five-core cable is required. It is inserted into the device through a rubber gasket and securely fixed. After this, all the conductors are attached to the corresponding terminals: grounding, zero and three phases.

The cores are attached to the terminals

The electric furnace cover is installed.

Step 2 . Stove mounting. The electrical appliance must be placed at least 15 cm from the floor. You will need 6x80 mm self-tapping screws. Since the weight of the unit can be significant, it is recommended to additionally install a mortgage in the wall at the location of the fasteners (under the cladding). Markings are applied for installing hardware. Two self-tapping screws are screwed in, on which the stove will hang.

Self-tapping screws are tightened

The heater is suspended on a mount.

Hanging stove

Step 4 . Preparing for work. Carefully, trying not to damage the heating elements, the stones are laid. They must be washed and dried. It is recommended to choose narrow stones that fit freely between the spirals of the heating element. They are not laid close to each other; there should be a small distance between them so that hot air can escape freely.

Laying stones

If you do come across large stones, it is better to lay them on top. The oven is ready for use.

Popular models

1. Polytechnic Cristina Classic. The model is suitable for a steam room with a volume of 10 - 15 cubic meters. meters, its power is 10 kW, the weight of stones is 25 kg, the price is 16,800 rubles.

2. Stream Gross 1 Heat boost. The stove is suitable for steam rooms with a volume of 8 - 14 cubic meters. meters, its power is 10 kW, the weight of the laid stones is 31.7 kg, the cost is 36,600 rubles.
3. Narvi NM600. Finnish product, recommended steam room volume 6 - 9 cubic meters. meters, furnace power 6 kW, weight of stones 30 - 40 kg, cost - 13,200 rubles.

4. Helo Himalaya 105DE. An electric furnace of Finnish-German production with a power of 10.5 kW is capable of heating a steam room with a volume of 9 - 15 cubic meters. meters, the weight of the stones being laid is 100 kg, it costs 50,500 rubles.

5. Harvia Cillindro PC70E Steel. Stove from Finland for steam rooms with a volume of 6 - 10 cubic meters. meters, power 6.9 kW, weight of laid stones 90 kg, cost - 17,400 rubles.

6. Tylo Combi Compact RC3. Swedish low-power stove of 3 kW, suitable for rooms with a volume of 1.5 - 4.5 cubic meters. meters, the weight of the stones is only 7 kg, the price is 67,000 rubles.

7. Tylo Expression 10. A more powerful electric sauna stove with a capacity of 10 kW, for steam rooms with a volume of 10 - 18 cubic meters. meters. It contains 12 kg of stones, and the price is 97,000 rubles.

8. Tylo SD 20. Powerful 20 kW device, for rooms with a volume of 22 - 43 cubic meters. meters, the weight of the stones being laid is 32 kg, the cost is 91,000 rubles.
   Read also:  We evaluate the pros and cons of glass doors to the steam room of Russian and Finnish baths, we figure out how to install, what sizes they come in and what reviews say
9. Thermofor Primavolta. This Russian-made electric sauna stove can heat a room of up to 5 cubic meters. meters, its maximum power is 9 kW. It holds 50 kg of stone and costs 12,000 rubles.

10. Dushka EKM-18 NMT. Russian powerful 18 kW stove for large steam rooms of 21 - 30 cubic meters. meters. You can put 65 kg of stone in it, the price is only 12,300 rubles.

SAWO SAVONIA SAV-80NB-Z

The compact heater is designed for medium-sized baths and saunas. The manufacturer used high-quality stainless steel and galvanization. TENs are protected from moisture. Due to this, the risk of damage to the device during operation is reduced. The operating mode of the device is set and regulated by the remote control.

Technical specifications:

• power – 8 kW;
• room volume – 7-13 cubic meters. m;
• weight of stones – up to 22 kg.

Pros:

• compactness;
• price;
• capacity;
• economical electricity consumption.

Rules for installing electric sauna stoves

Requirements SNiP 41-01-2003

This document regulates the basic rules for placing electric furnaces from a fire safety point of view:

• The stove must be installed in a corner closer to the entrance, however, subject to the requirements of SNiP, installation in the center of the room is also allowed.
• The floor where the stove is installed is covered with non-combustible materials.
• The distance between the wall and the furnace body must be at least 0.5 meters in the absence of a screen. If such protection is installed, it is allowed to place the electric oven closer.
• There should be a hole in the area of ​​the heater for fresh ventilation.
• The furnace body must be protected by a fence located at a distance of at least 70 cm.

.

How to install the housing and controls?

The first step is to wash and dry the stones, place them and turn on the stove. When connecting an empty stove, the heating elements will burn out. When installing the control panel, the following requirements must be met:

• The external remote control is installed in a room where there are no elevated temperatures.
• The wiring is done in advance.
• The power that the electrical panel and wires can withstand must not be lower than the power of the electric furnace.
• The presence of an RCD is required.
• In order to avoid contact between wires and heated walls, they are laid in a special bus made of fireproof material.

Installation of sensors and grounding

It is recommended to use only cables made of heat-resistant material. The presence of twists is excluded; all wire sections must be intact. Sensors are usually mounted above the door, heater and steam benches.

GOST 12.1.030-81 requirements and electrical wiring cross-section

According to GOST 12.1.030-81, the electrical circuit must be grounded directly or grounded through the shield. As mentioned above, the power that the wiring can withstand must be higher than the power of the furnace itself. The selection of conductor cross-sections is made according to special tables.

.

Types of metals

The body and internal components can be made of various types of materials; cast iron specimens are durable and have high heat transfer, but are quite bulky and heavy.

Stainless steel will be lighter and less massive and has a number of advantages, including an attractive appearance. Enameled steel is used in rare cases, but some people use such devices to equip steam rooms.

Nuances of operation

The electric furnace does not require particularly careful maintenance, but you still need to follow the basic rules of its operation. The main point is compliance with the rules of electrical safety and ventilation of steam rooms.

Do not allow water to come into contact with wires or electrical heating parts of the oven. In the steam room, you should always ensure the minimum permissible air circulation. To avoid rapid burnout of the heating elements, the load must be applied smoothly immediately after starting the furnace.

Final points

A sauna with an electric stove is a powerful consumer of electricity. When choosing, it will be very important to pay attention to the electricity consumption of the stove; this will save significant amounts, even if the stove is quite expensive.

From an aesthetic point of view, foreign models are superior to their Russian counterparts, but they are also more expensive. Specific options should be considered based on financial capabilities when purchasing, as well as taking into account the volume of the steam room and the power that the electrical wiring and transformer can withstand.

A heating element

To complete the equipment, special heating elements are most often used; they can be of a strip type or a combined type. The cost of such a device is not too high and it can be replaced at any time if a breakdown occurs.

It will not be possible to operate such elements for a long time, this is due to the fact that they are often subjected to mechanical stress. When purchasing an item, it would be advisable to choose models with high-quality alloy in this element.